$ 30.00
The 6-inch Alien on Beach Decal Rig is a compact glass dab rig built for concentrate enthusiasts who want something fun for their desk or coffee table without taking up too much space. It comes ready to use with a 14mm male 90-degree quartz banger included, so you can start dabbing right out of the box. The clear glass body features a quirky alien beach scene decal that adds personality to an otherwise straightforward rig.
This one's built for casual dabbers and newcomers who want an affordable entry point into concentrate consumption. If you're coming from flower and curious about dabbing, or you need a backup rig that doesn't hurt to replace, this fits the bill. The included banger means you're not piecing together a setup from scratch. It's also solid for anyone who appreciates a bit of weird artwork on their gear — the alien chilling on a beach is oddly relaxing.
Not the rig for marathon sessions or collectors chasing American glass. This is a functional daily driver at a friendly price point.
Fill the rig with just enough water to cover the downstem opening — usually about an inch or so from the base. You want bubbles when you pull, but not water splashing up toward your mouth. Too much water creates drag and makes hits feel restricted.
Heat the included banger with a butane torch until the bottom glows slightly, then let it cool for 30-45 seconds depending on thickness. The goal is a temperature hot enough to vaporize your concentrate without scorching it. Overheating destroys flavor and wastes material. Underheating leaves puddles that don't vaporize properly.
Drop your concentrate into the banger using a dab tool, cap it with a carb cap to restrict airflow, and inhale slowly. The carb cap creates convection that helps vaporize everything in the dish. Without one, you're leaving terpenes and material behind.
After each session, wipe the banger with a cotton swab while it's still warm. This prevents char buildup that eventually ruins quartz and affects flavor. A clean banger tastes better and lasts longer.
| Spec | Detail |
|---|---|
| Height | 6 inches (152mm) |
| Material | Clear glass with decal design |
| Joint size | 14mm female |
| Joint angle | 90 degrees |
| Included | 14mm male quartz banger |
| Design | Alien on beach scene |
The 14mm female joint accepts any 14mm male banger, nail, or accessory at a 90-degree angle. This is one of the most common joint configurations in dabbing, so you'll have plenty of upgrade options when you're ready. The included banger works fine for getting started, but serious flavor chasers might eventually want to swap in a thicker quartz banger or terp slurper for better heat retention.
The 90-degree angle is important if you're shopping for replacement bangers — a 45-degree banger won't sit properly and will angle your torch in awkward directions. Stick with 90-degree pieces for this rig.
Let everything cool completely before cleaning. For the rig body, pour out old water after each session and rinse with warm water. Weekly deep cleans with isopropyl alcohol and coarse salt shake out residue that builds up in hard-to-reach spots. Rinse thoroughly and let dry before using again.
The banger needs more frequent attention. Wipe it with a dry cotton swab after every dab while it's still warm. For stubborn char, soak the banger in isopropyl alcohol overnight, then gently scrape with a dabber tool. Heavily charred bangers eventually need replacing — no amount of cleaning brings back a burned dish.
Store the rig on a dab mat to protect the base from hard surfaces and keep sticky residue off your furniture.
Technically you could add a 14mm bowl instead of the banger, but this rig is designed for concentrates. The small chamber and lack of percolation make it less ideal for flower. You'd get harsh, hot hits. If you want something for flower, check out a dedicated water pipe with better filtration.
Decals on glass rigs are typically applied under the outer layer or sealed, so normal use shouldn't affect them. Avoid soaking the outside of the rig in alcohol for extended periods — stick to cleaning the inside where residue actually builds up. The decal should hold up fine with reasonable care.
Most dabbers aim for 450-550°F for flavor-forward low-temp dabs, or 550-650°F for bigger clouds with less flavor. Without a temp gun, heat until you see a faint glow, then wait 30-45 seconds. Every banger is different, so experiment to find your sweet spot. Burned, harsh hits mean you're going too hot.
Yes. The rig comes with the banger but no carb cap. You can technically dab without one, but you'll waste concentrate and get weaker hits. A basic bubble cap or directional cap makes a noticeable difference in vapor production and efficiency. They're inexpensive and worth grabbing.
Just enough to cover the bottom of the downstem — usually about an inch from the base. When you inhale, you should see bubbles but not feel water splashing up. Too much water creates resistance and can splash into the banger if you pull hard.
Cold starts work with most bangers, including the one included here. Load your concentrate into the cold banger, cap it, then apply heat gradually while inhaling slowly. Stop heating once vapor starts forming. Cold starts are gentler on the quartz and can preserve more terpenes, though some people prefer traditional hot starts for bigger clouds.
It's glass, so yes — treat it accordingly. The 6-inch compact size actually helps since there's less leverage to tip over, but drops onto hard surfaces will break it. Keep it on a padded mat, don't knock it around, and it'll last. If durability is your priority, silicone rigs are nearly indestructible alternatives.