2″ 14 M 90° RICK & MORTY RECLAIM CATCHER

The 2″ 14M 90° Rick & Morty Reclaim Catcher is a glass add-on made for flower heads who love the show but hate a gunked-up piece. Built for 14mm setups with a 90° joint, it helps keep your rig cleaner by catching residue before it builds up in your main piece. At just 2 inches (50.8mm), it adds function without turning your daily driver into a science project.

Why You’ll Actually Use This

• Keep your rig cleaner, longer — Reclaim drops into the catcher instead of coating the inside of your piece, so you’re not deep-cleaning every other day.
• Save your flavor — Less buildup in your main chamber means smoother hits and less “mystery gunk” taste when you’re a few bowls in.
• Drop-in upgrade — 14mm male, 90° angle means it slots right into most standard water pipes and rigs that use 14mm female joints.
• Rick & Morty vibes — Themed graphics give your setup that cartoon chaos energy without looking like a toy.
• Compact add-on — At 2 inches (50.8mm), it adds function without turning your glass into a tall, tipsy tower.
• Easy reclaim dump — When it builds up, just remove the catcher and clear it out instead of wrestling with your whole rig in the sink.

Best For

This reclaim catcher is made for flower smokers and hybrid smokers who are tired of scrubbing down their favorite 14mm glass after every few bowls. It’s a smart add-on if your piece is your daily driver and you’d rather be packing fresh green than soaking glass every weekend. If you’re already running a full station with a dab mat and a few tools on deck, this slots right into that setup without drama.

How to Use It

Using it is as simple as adding one extra piece to your normal setup. The 14mm male joint on the reclaim catcher plugs into the 14mm female joint on your rig or water pipe, sitting at a 90° angle so everything lines up clean and doesn’t feel awkward in the hand.

Your bowl or accessory then goes onto the top joint of the catcher (matching size/gender). As you burn through bowls, residue that would normally bake itself onto the inside of your pipe gets intercepted and settles in the reclaim catcher instead. When you notice it starting to build up, pop it off, clear it out, and you’re back to a cleaner piece with a lot less effort. Pair it with a heavy-bottom jar from our concentrate jars lineup if you like keeping your station extra dialed in.

For storage and travel, you can pull the catcher off your piece and tuck it safely with the rest of your storage & packaging so you’re not risking it rolling off a shelf or getting bumped.

Specs

Fit & Compatibility

This reclaim catcher is built around a 14mm male joint at a 90° angle, so it plays best with water pipes and rigs that have a 14mm female joint set at 90°. If your bowl or other attachment matches that joint size and angle, this drops in smoothly as the middle piece of your setup.

Because it’s glass and not silicone, it blends well with most standard glass rigs and bongs you’ll find in the smoke shop products section, especially anything that already runs a 14mm joint system.

Cleaning & Care

Let the glass cool fully before you mess with it. When it’s cool, you can tap or wipe out loose residue. For a deeper clean, soak the catcher in isopropyl alcohol, rinse with warm water, and let it dry completely before putting it back on your piece.

FAQ

• Will this fit my rig or bong?
  If your piece has a 14mm female joint at a 90° angle, you’re good. The catcher has a 14mm male joint that plugs into that, and your 14mm bowl or accessory goes on top. If your joint is 45° or a different size, this specific catcher won’t line up correctly.
• Is this only for flower, or can I use it with other setups?
  It’s listed under flower accessories, but it can sit between your piece and other 14mm attachments as long as the joint sizes and angles all match. If you’re experimenting with different attachments, the same logic applies as with dab tools: match size and style so everything sits secure.
• How often should I empty or clean the reclaim catcher?
  That depends how hard you run your piece. Heavy daily drivers might want to clear it every few seshes so airflow stays open and your setup doesn’t feel restricted. If you notice more drag or see visible buildup, it’s time for a quick clean.
• Is the Rick & Morty design printed or part of the glass?
  Themed graphics are applied to the outside of the glass. Treat it like any other printed glass piece: avoid harsh scrubbing directly on the art so it keeps looking sharp. A quick soak and light wipe does the job.
• Will this make my piece tip over or feel awkward?
  The catcher is only 2 inches (50.8mm) long, so it doesn’t add a lot of leverage or bulk. On a reasonably sturdy base, it feels like a small extension, not a massive arm hanging off the side. If your piece is already top-heavy, just be extra mindful setting it down.
• Can I use this with other Rick & Morty themed glass?
  As long as the other piece has a 14mm female joint at 90°, it’ll pair up just fine. A matching rig or water pipe plus this catcher and a themed bowl makes a fun little set, similar to putting together a full silicone rig and accessory combo from our silicone bongs & rigs lineup.
• What’s the best way to store it when I’m not using it?
  Treat it like any other small glass accessory: keep it in a padded spot, away from hard edges and random clutter that can knock it around. Some people keep these in a small box or case alongside extra bowls, carb caps, or other glass accessories so everything’s in one place and less likely to get broken.

If you’re into keeping your setup cleaner without turning maintenance into a whole project—and you like a little Rick & Morty chaos on your glass—this reclaim catcher is an easy, low-cost upgrade that’ll pay for itself in fewer deep cleans and smoother seshes.

"}